FRNC-5PC工藝計算軟件操作指南(DOC 34頁)
FRNC-5PC工藝計算軟件操作指南(DOC 34頁)內容簡介
1......總則......3
1.1 主要應用......3
1.2 相關標準及參考書籍......3
2......軟件簡介......4
2.1軟件使用範圍......4
2.1軟件計算方法......5
2.1.1固定發熱量(固定燃料量)......5
2.1.2固定熱負荷......5
3......輸入部分......6
3.1 燃燒室輸入......6
3.1.1 Characteristic......6
3.1.2 Furnace type......7
3.1.3 Furnace dimension......8
3.1.4 Flue Gas “Take-Off”......9
3.1.5 The ID’s of Coil Sections in Firebox......9
3.2 對流室輸入......10
3.2.1 Characteristic......10
3.2.2 Internal Duct Dimensions......11
3.2.3 Coil Section, Q-Bank, or Air Preheater ID......11
3.3 煙囪輸入......11
3.3.1 Characteristic......11
3.3.2 Geometry......12
3.4管路輸入......12
3.4.1 Geometry......13
3.4. 2 Process fluid......13
3.4.3 Geometry I......14
3.4.4 Geometry II......14
3.4.5 Additional data......16
3.4.6 Additional data......17
3.5爐管數據輸入......18
3.5.1 General characteristics......18
3.5.2 Fin type and diameter......19
3.5.3 Fin data......20
3.6物料數據輸入......21
3.6.1 Process stream Characteristic......21
3.6.2Condition......21
3.7燃燒數據輸入......22
3.7.1 Firing data......22
3.7.2 Bridge wall temperature......24
3.7.3 Fuel #1......24
3.8燃料數據輸入......25
3.8.1 Identification......25
3.8.2 Composition......26
3.9熱損失輸入......27
3.10注入水蒸氣/水數據......27
3.11Q-BANK輸入......28
3.12空氣數據輸入......29
3.13空氣預熱器輸入......30
3.13.1 General Characteristic......30
3.13.2 Specification......30
3.14物理數據輸入......31
3.14.1 自動生成的物理性質......32
3.14.2 直接輸入的物理數據......32
3.14.3 僅僅生成的物理屬性數據......32
4......輸出部分......32
4.1輸入數據的重現......32
4.2輸入數據的處理......33
4.3物理屬性數據的重現......33
4.4計算過程輸出......33
4.4最終結果輸出......33
..............................
1.1 主要應用......3
1.2 相關標準及參考書籍......3
2......軟件簡介......4
2.1軟件使用範圍......4
2.1軟件計算方法......5
2.1.1固定發熱量(固定燃料量)......5
2.1.2固定熱負荷......5
3......輸入部分......6
3.1 燃燒室輸入......6
3.1.1 Characteristic......6
3.1.2 Furnace type......7
3.1.3 Furnace dimension......8
3.1.4 Flue Gas “Take-Off”......9
3.1.5 The ID’s of Coil Sections in Firebox......9
3.2 對流室輸入......10
3.2.1 Characteristic......10
3.2.2 Internal Duct Dimensions......11
3.2.3 Coil Section, Q-Bank, or Air Preheater ID......11
3.3 煙囪輸入......11
3.3.1 Characteristic......11
3.3.2 Geometry......12
3.4管路輸入......12
3.4.1 Geometry......13
3.4. 2 Process fluid......13
3.4.3 Geometry I......14
3.4.4 Geometry II......14
3.4.5 Additional data......16
3.4.6 Additional data......17
3.5爐管數據輸入......18
3.5.1 General characteristics......18
3.5.2 Fin type and diameter......19
3.5.3 Fin data......20
3.6物料數據輸入......21
3.6.1 Process stream Characteristic......21
3.6.2Condition......21
3.7燃燒數據輸入......22
3.7.1 Firing data......22
3.7.2 Bridge wall temperature......24
3.7.3 Fuel #1......24
3.8燃料數據輸入......25
3.8.1 Identification......25
3.8.2 Composition......26
3.9熱損失輸入......27
3.10注入水蒸氣/水數據......27
3.11Q-BANK輸入......28
3.12空氣數據輸入......29
3.13空氣預熱器輸入......30
3.13.1 General Characteristic......30
3.13.2 Specification......30
3.14物理數據輸入......31
3.14.1 自動生成的物理性質......32
3.14.2 直接輸入的物理數據......32
3.14.3 僅僅生成的物理屬性數據......32
4......輸出部分......32
4.1輸入數據的重現......32
4.2輸入數據的處理......33
4.3物理屬性數據的重現......33
4.4計算過程輸出......33
4.4最終結果輸出......33
..............................
用戶登陸
工藝技術熱門資料
工藝技術相關下載